# # olsr.org OLSR daemon config file # # Lines starting with a # are discarded # # This file was shipped with olsrd 0.X.X # # This file is an example of a typical # configuration for a mostly static # network(regarding mobility) using # the LQ extention # Debug level(0-9) # If set to 0 the daemon runs in the background DebugLevel 1 # Fisheye mechanism for TC messages 0=off, 1=on LinkQualityFishEye 1 LinkQualityDijkstraLimit 0 10.0 # IP version to use (4 or 6) IpVersion 4 # Clear the screen each time the internal state changes ClearScreen yes # HNA IPv4 routes # syntax: netaddr netmask # Example Internet gateway: # 0.0.0.0 0.0.0.0 Hna4 { # Internet gateway: # 0.0.0.0 0.0.0.0 # more entries can be added: # 192.168.1.0 255.255.255.0 } # HNA IPv6 routes # syntax: netaddr prefix # Example Internet gateway: Hna6 { # Internet gateway: # :: 0 # more entries can be added: # fec0:2200:106:: 48 } # Should olsrd keep on running even if there are # no interfaces available? This is a good idea # for a PCMCIA/USB hotswap environment. # "yes" OR "no" AllowNoInt yes # TOS(type of service) value for # the IP header of control traffic. # If not set it will default to 16 #TosValue 16 # The fixed willingness to use(0-7) # If not set willingness will be calculated # dynamically based on battery/power status # if such information is available Willingness 6 # Allow processes like the GUI front-end # to connect to the daemon. IpcConnect { # Determines how many simultaneously # IPC connections that will be allowed # Setting this to 0 disables IPC MaxConnections 0 # By default only 127.0.0.1 is allowed # to connect. Here allowed hosts can # be added Host 127.0.0.1 #Host 10.0.0.5 # You can also specify entire net-ranges # that are allowed to connect. Multiple # entries are allowed #Net 192.168.1.0 255.255.255.0 } # Wether to use hysteresis or not # Hysteresis adds more robustness to the # link sensing but delays neighbor registration. # Used by default. 'yes' or 'no' # Do not use hysteresis with ETX! UseHysteresis no # Hysteresis parameters # Do not alter these unless you know # what you are doing! # Set to auto by default. Allowed # values are floating point values # in the interval 0,1 # THR_LOW must always be lower than # THR_HIGH. #HystScaling 0.50 #HystThrHigh 0.80 #HystThrLow 0.30 # Link quality level # 0 = do not use link quality # 1 = use link quality for MPR selection # 2 = use link quality for MPR selection and routing # Defaults to 0 LinkQualityLevel 2 # Link quality window size # Defaults to 10 LinkQualityWinSize 100 # Policy Routing Table Number RtTable 254 # How to insert metric values: flat, approx, exact FIBMetric "approx" # Multiplier for comparing old ETX to new ETX for 0/0 routes NatThreshold 0.75 # Polling rate in seconds(float). # Default value 0.05 sec Pollrate 0.025 # TC redundancy # Specifies how much neighbor info should # be sent in TC messages # Possible values are: # 0 - only send MPR selectors # 1 - send MPR selectors and MPRs # 2 - send all neighbors # # defaults to 0 TcRedundancy 2 # # MPR coverage # Specifies how many MPRs a node should # try select to reach every 2 hop neighbor # # Can be set to any integer >0 # # defaults to 1 MprCoverage 5 # Olsrd plugins to load # This must be the absolute path to the file # or the loader will use the following scheme: # - Try the paths in the LD_LIBRARY_PATH # environment variable. # - The list of libraries cached in /etc/ld.so.cache # - /lib, followed by /usr/lib # Example plugin entry with parameters: #LoadPlugin "olsrd_dyn_gw.so.0.3" #{ # Here parameters are set to be sent to the # plugin. Theese are on the form "key" "value". # Parameters ofcause, differs from plugin to plugin. # Consult the documentation of your plugin for details. # Example: dyn_gw params # how often to check for Internet connectivity # defaults to 5 secs # PlParam "Interval" "40" # if one or more IPv4 addresses are given, do a ping on these in # descending order to validate that there is not only an entry in # routing table, but also a real internet connection. If any of # these addresses could be pinged successfully, the test was # succesful, i.e. if the ping on the 1st address was successful,the # 2nd won't be pinged # PlParam "Ping" "141.1.1.1" # PlParam "Ping" "194.25.2.129" #} LoadPlugin "olsrd_httpinfo.so.0.1" { PlParam "Port" "8080" PlParam "Net" "0.0.0.0 0.0.0.0" } LoadPlugin "olsrd_txtinfo.so.0.1" { PlParam "accept" "127.0.0.1" } LoadPlugin "olsrd_dyn_gw_plain.so.0.4" { } LoadPlugin "olsrd_arprefresh.so.0.1" { } #LoadPlugin "olsrd_nameservice.so.0.3" #{ #PlParam "suffix" ".olsr" #PlParam "interval" "180" #PlParam "timeout" "3600" #PlParam "latlon-file" "/var/run/latlon.js" #PlParam "lat" "52.495332" #PlParam "lon" "13.454122" #} #LoadPlugin "olsrd_dot_draw.so.0.3" #{ # accept connection from IP: # default 127.0.0.1 (localhost) #PlParam "accept" "192.168.0.5" #} # Interfaces and their rules # Omitted options will be set to the # default values. Multiple interfaces # can be specified in the same block # and multiple blocks can be set. # !!CHANGE THE INTERFACE LABEL(s) TO MATCH YOUR INTERFACE(s)!! # (eg. wlan0 or eth1): Interface "wlan0" "wlan1" "ath0" "ath1" { # IPv4 broadcast address to use. The # one usefull example would be 255.255.255.255 # If not defined the broadcastaddress # every card is configured with is used # Ip4Broadcast 255.255.255.255 # IPv6 address scope to use. # Must be 'site-local' or 'global' # Ip6AddrType site-local # IPv6 multicast address to use when # using site-local addresses. # If not defined, ff05::15 is used # Ip6MulticastSite ff05::11 # IPv6 multicast address to use when # using global addresses # If not defined, ff0e::1 is used # Ip6MulticastGlobal ff0e::1 # Emission intervals. # If not defined, RFC proposed values will # be used in most cases. # Hello interval in seconds(float) HelloInterval 5.0 # HELLO validity time HelloValidityTime 125.0 # TC interval in seconds(float) TcInterval 2.0 # TC validity time TcValidityTime 500.0 # MID interval in seconds(float) MidInterval 25.0 # MID validity time MidValidityTime 500.0 # HNA interval in seconds(float) HnaInterval 25.0 # HNA validity time HnaValidityTime 500.0 # When multiple links exist between hosts # the weight of interface is used to determine # the link to use. Normally the weight is # automatically calculated by olsrd based # on the characteristics of the interface, # but here you can specify a fixed value. # Olsrd will choose links with the lowest value. # Weight 0 # If a certain route should be preferred # or ignored by the mesh, the Link Quality # value of a node can be multiplied with a factor # entered here. In the example the route # using 192.168.0.1 would rather be ignored. # A multiplier of 0.5 will result in a small # (bad) LinkQuality value and a high (bad) # ETX value. # LinkQualityMult 192.168.0.1 0.5 # This multiplier applies to all other nodes # LinkQualityMult default 0.8 }